American Type Culture Collection (ATCC) Logo American Type Culture Collection (ATCC) Logo 0
  • Quick Order
  • Careers
  • Support

Exiguobacterium aurantiacum Collins et al.

BAA-333

Download Genome Learn about the ATCC Genome Portal
Product category
Bacteria
Product type
Extremophile
Strain designation
Colo. Road
Type strain
No
Genome sequenced strain
Yes
Isolation source
Microbial mat in Pinkerton hot spring, north of Durango
Geographical isolation
United States; Colorado; Durango
Product format
Freeze-dried
Mission Collection Item
This is a Mission Collection Item.

Documentation

ATCC determines the biosafety level of a material based on our risk assessment as guided by the current edition of Biosafety in Microbiological and Biomedical Laboratories (BMBL), U.S. Department of Health and Human Services. It is your responsibility to understand the hazards associated with the material per your organization’s policies and procedures as well as any other applicable regulations as enforced by your local or national agencies.

ATCC highly recommends that appropriate personal protective equipment is always used when handling vials. For cultures that require storage in liquid nitrogen, it is important to note that some vials may leak when submersed in liquid nitrogen and will slowly fill with liquid nitrogen. Upon thawing, the conversion of the liquid nitrogen back to its gas phase may result in the vial exploding or blowing off its cap with dangerous force creating flying debris. Unless necessary, ATCC recommends that these cultures be stored in the vapor phase of liquid nitrogen rather than submersed in liquid nitrogen.

Detailed product information

General

Preceptrol
No

Characteristics

Extremophile type
Alkaliphile

Handling information

Medium
Temperature
37°C
Atmosphere
Aerobic
Handling procedure
1. Open vial according to enclosed instructions.

2. Using a single tube of #461 broth (5 to 6 ml), withdraw approximately 0.6 ml with a Pasteur or 1.0 ml pipette.  Rehydrate the entire pellet.

3. Aseptically transfer 0.3 ml of this suspension back into the broth tube.  Mix well.

4. Use the remaining 0.3 ml of the suspension to inoculate a slant of #260 or #461 agar.

5. Incubate tubes at 37oC for 24 hours.

6. Once growth is obtained in broth, plates can be inoculated with approximately 0.2 ml per plate

Handling notes

Turbid growth should be visible in broth after 24 to 48 hours of incubation.  After 24 to 48 hours, colonies on #461 plates are yellow/orange, irregular, flat, erose and have a darker center.  On #260 agar, the colonies exhibit a-hemolysis with a green discoloration of the media.

Quality control specifications

Verification method
Whole-genome Sequencing

History

Deposited as
Exiguobacterium aurantiacum Collins et al.
Depositors
RF Ramaley
Type of isolate
Environmental
Year of origin
2000
Special collection
NSF - Bacteriology
Cross references
GenBank AY047481 Exiguobacterium aurantiacum var. Colo. Road 16S ribosomal RNA gene, partial sequence.

Legal disclaimers

Intended use
This product is intended for laboratory research use only. It is not intended for any animal or human therapeutic use, any human or animal consumption, or any diagnostic use.
Warranty

The product is provided 'AS IS' and the viability of ATCC® products is warranted for 30 days from the date of shipment, provided that the customer has stored and handled the product according to the information included on the product information sheet, website, and Certificate of Analysis. For living cultures, ATCC lists the media formulation and reagents that have been found to be effective for the product. While other unspecified media and reagents may also produce satisfactory results, a change in the ATCC and/or depositor-recommended protocols may affect the recovery, growth, and/or function of the product. If an alternative medium formulation or reagent is used, the ATCC warranty for viability is no longer valid.  Except as expressly set forth herein, no other warranties of any kind are provided, express or implied, including, but not limited to, any implied warranties of merchantability, fitness for a particular purpose, manufacture according to cGMP standards, typicality, safety, accuracy, and/or noninfringement.

Disclaimers

This product is intended for laboratory research use only. It is not intended for any animal or human therapeutic use, any human or animal consumption, or any diagnostic use. Any proposed commercial use is prohibited without a license from ATCC.

While ATCC uses reasonable efforts to include accurate and up-to-date information on this product sheet, ATCC makes no warranties or representations as to its accuracy. Citations from scientific literature and patents are provided for informational purposes only. ATCC does not warrant that such information has been confirmed to be accurate or complete and the customer bears the sole responsibility of confirming the accuracy and completeness of any such information.

This product is sent on the condition that the customer is responsible for and assumes all risk and responsibility in connection with the receipt, handling, storage, disposal, and use of the ATCC product including without limitation taking all appropriate safety and handling precautions to minimize health or environmental risk. As a condition of receiving the material, the customer agrees that any activity undertaken with the ATCC product and any progeny or modifications will be conducted in compliance with all applicable laws, regulations, and guidelines. This product is provided 'AS IS' with no representations or warranties whatsoever except as expressly set forth herein and in no event shall ATCC, its parents, subsidiaries, directors, officers, agents, employees, assigns, successors, and affiliates be liable for indirect, special, incidental, or consequential damages of any kind in connection with or arising out of the customer's use of the product. While reasonable effort is made to ensure authenticity and reliability of materials on deposit, ATCC is not liable for damages arising from the misidentification or misrepresentation of such materials.

Please see the material transfer agreement (MTA) for further details regarding the use of this product. The MTA is available at www.atcc.org.

Permits & Restrictions

Import Permit for the State of Hawaii

If shipping to the U.S. state of Hawaii, you must provide either an import permit or documentation stating that an import permit is not required. We cannot ship this item until we receive this documentation. Contact the Hawaii Department of Agriculture (HDOA), Plant Industry Division, Plant Quarantine Branch to determine if an import permit is required.

MORE INFORMATION ABOUT PERMITS AND RESTRICTIONS

Frequently Asked Questions

References

Curated Citations

Robert F Ramaley, personal communication

For product-related inquiries and issues, contact Technical Service:

Message Us

Hours of Operation

Monday - Friday
9:00am - 5:00pm
US Eastern Time